How to Measure Corn Harvest Losses Before Adjusting Your Combine

18 November 2026
Editorial illustration of a sampling frame on soil among corn stubble, with a hand pointing to loose kernels and the headline “Count Corn Loss Before Changing Settings.”

Turn scattered kernels into a useful loss estimate

Those corn kernels scattered across the field can tell you whether your combine needs adjusting. But before changing settings, find out how much grain you're actually losing during harvest. Count loose kernels in measured areas, compare what was on the ground before harvesting with what appears afterward, and include dropped ears in your estimate. The goal is to measure losses caused by the harvesting pass – not blame the combine for corn that was already on the ground.

Count across the harvest width

Don't rely on one patch with an unusually heavy concentration of kernels. Check several representative locations across the harvest width to get a better picture of actual field losses. Start with a baseline count in nearby, representative unharvested corn. After the combine passes, repeat the count in comparable measured areas.

Nebraska Extension's harvest-loss guide provides a useful rule of thumb:
– 20 corn kernels in 10 square feet equal approximately 1 bushel per acre of loss.
That's about two kernels per square foot for every bushel per acre.

The formula:
– Estimated loose-kernel loss (bu/acre) = (Total kernels counted ÷ Total square feet sampled) ÷ 2
If you sample several areas, add all the kernel counts and sampled areas before calculating the average loss.

This is an approximate field estimate because kernel size and weight can vary. Keep kernels attached to dropped ears out of this count; those losses are measured separately.

Subtract what was already on the ground

Don't let preharvest wind, lodging or dropped grain distort your estimate. If kernels were already on the ground before harvesting, counting everything behind the combine makes the machine appear responsible for more loss than it actually caused.

Here's an example using assumed counts:
– After harvest: 40 kernels in 10 sq. ft. = 40 ÷ 10 ÷ 2 = 2 bu/acre.
– Before harvest: 10 kernels in 10 sq. ft. = 10 ÷ 10 ÷ 2 = 0.5 bu/acre.
– Added during harvesting: 2 − 0.5 = 1.5 bu/acre of loose-kernel loss.

That means the harvesting pass added approximately 1.5 bushels per acre—not the full 2 bushels found afterward. This number still excludes dropped ears and doesn't identify whether the kernels were lost at the corn head or farther through the combine.

Include whole and partial ears

Loose kernels are only part of the story. A single missed or dropped ear can contain hundreds of kernels, adding substantially to harvest losses. Following Nebraska Extension's method, measure a 1/100-acre area (435.6 square feet) across the harvested rows and collect the dropped ears. Each ¾-pound ear—or an equivalent amount in smaller ears—represents approximately 1 bushel per acre of loss in that measured area.

Don't count every ear as equal regardless of its size. Check a comparable unharvested area for ears that were already on the ground before the combine arrived. Subtract those preharvest losses from the post-harvest ear-loss estimate. Then add the remaining ear loss to the loose-kernel loss associated with the harvesting pass. This gives you a more complete estimate of how much corn the harvesting operation left behind.

Use the result to target one adjustment

University of Minnesota Extension recommends keeping combine losses below 1 bushel per acre under normal conditions. In our example, the harvesting pass added approximately 1.5 bushels per acre in loose kernels alone. That's already above the normal-condition benchmark, even before accounting for dropped ears. But before changing combine settings, find out where the grain is being lost.

Two main sources deserve attention:
– Header loss: Dropped or missed ears and loose kernels shelled at the corn head.
– Rear-end loss: Grain escaping through the threshing, separating or cleaning systems.

To help identify the source, safely stop and move the combine clear of the sampling area. With the machine shut down, compare kernel counts in the area passed over by the corn head but not the rear discharge with counts behind the complete machine. This helps distinguish grain lost at the header from additional grain discharged farther through the combine.

Iowa State University Extension's September 9, 2026 guidance recommends starting with the manufacturer's suggested settings and adapting them to actual field conditions. Change one setting at a time. Then run another test strip under comparable conditions and measure losses again. Recheck after significant changes in crop moisture, hybrid, wind, lodging or other field conditions. Settings that worked earlier in the day may not deliver the same results later.

The objective is simple: measure the loss, identify its source and make adjustments that keep more corn in the grain tank.